chris1
POCKETBIKE NUT,
- Joined
- Oct 18, 2002
- Posts
- 10,830
(Japanese Taito F3 motherboard)
Taito F3 info needed.
General info ...A website etc..
Anything I should know otherwise about Taito F3....not found at Briggs site..http://www.hardmvs.com/
(I would like to put this in the little BAM cab,.....With the 1 slot still in the cab.....Cab is Mono.
Does this Mother board require -5V..
Is the Taito F3 Mono or Stereo.......?.Switchable
I guess this would answer my question as to if I can play other Region games on a Japanese Motherboard.
http://www.hardmvs.com/F3/F3modify.htm Modifying the F3 for all regions
The F3 system is keyed for different regions. Unfortunately, the keying is physical, and not done through a BIOS.
(So do I just take these Keys off and leave them off..?
Where is the Volume Control?..How do I adjust it.
This is another 4 pin connector. Also note above the pot marked "VR1" That is NOT a volume control. It is used to adjust the voltage at the PCB. Don't mess with it or you will screw the PCB up
Any Must buy or recomended games.?
Do I need to put in a 4 way joystick instead of an 8 way....Does it matter..?Will playing this with an 8 way mess something up.?
Pop 'n Pop
Joystick: 4-way (up, down, left, right)
Buttons: 2
http://www.klov.com/P/Pop_'n_Pop.html
............................................................................................
I'm assuming this cart above/my cart is.....Below..
Puzzle Bobble 2 (Bust-A-Move Again)
Puzzle Bobble 2
Joystick: 8-way
Buttons: 1
http://www.klov.com/P/Puzzle_Bobble_2.html
.................................................
NOTE:
None of this stuff is in my possession yet..So I can't look at anything in hand to see what's what yet..
So far I bought ..
A Japanese Taito F3 motherboard.
Puzzle Bobble 2 Taito F3 Cart.
Pop N Pop Taito F3 Cart.
I got out of the CPSII and into this.
Taito F3 info needed.
General info ...A website etc..
Anything I should know otherwise about Taito F3....not found at Briggs site..http://www.hardmvs.com/
(I would like to put this in the little BAM cab,.....With the 1 slot still in the cab.....Cab is Mono.
Does this Mother board require -5V..
Is the Taito F3 Mono or Stereo.......?.Switchable
I guess this would answer my question as to if I can play other Region games on a Japanese Motherboard.
http://www.hardmvs.com/F3/F3modify.htm Modifying the F3 for all regions
The F3 system is keyed for different regions. Unfortunately, the keying is physical, and not done through a BIOS.
(So do I just take these Keys off and leave them off..?
Where is the Volume Control?..How do I adjust it.
This is another 4 pin connector. Also note above the pot marked "VR1" That is NOT a volume control. It is used to adjust the voltage at the PCB. Don't mess with it or you will screw the PCB up
Any Must buy or recomended games.?
Do I need to put in a 4 way joystick instead of an 8 way....Does it matter..?Will playing this with an 8 way mess something up.?
Pop 'n Pop
Joystick: 4-way (up, down, left, right)
Buttons: 2
http://www.klov.com/P/Pop_'n_Pop.html
............................................................................................
I'm assuming this cart above/my cart is.....Below..
Puzzle Bobble 2 (Bust-A-Move Again)
Puzzle Bobble 2
Joystick: 8-way
Buttons: 1
http://www.klov.com/P/Puzzle_Bobble_2.html
.................................................
NOTE:
None of this stuff is in my possession yet..So I can't look at anything in hand to see what's what yet..
So far I bought ..
A Japanese Taito F3 motherboard.
Puzzle Bobble 2 Taito F3 Cart.
Pop N Pop Taito F3 Cart.
I got out of the CPSII and into this.