Following games for sale, all original and in full working order except where noted otherwise:
Puzzle Bobble 3 - 100% $100
Zero Wing - 100%,two player simultaneous play version! $100
F/A - (Japanese Fighter & Attacker) works flawless. SOLD
Asterix - Plays, has some graphics glitches, looks to be either a RAM or ROM failure, self diagnostic passes though. Have resoldered all surface mount chips when I bought it (Bought it completely dead, caught in a reset loop) so the error is not a problem with the SMD components! $30 takes it
Time Scanner - 100% $80
Cadillacs & Dinosaurs Turbo 97- Bootleg, works SOLD
Cadillacs & Dinosaurs Turbo 2000 - Bootleg, overlay graphics glitching and jumping about, should be a fairly easy fix, missing sound amp. $15
Sunset Riders - Bootleg, graphics glitches, plays blind Problem is probably the PLCC socket/chip legs are tarnished, previous 'repairman' put solder onto the chip legs, needs a little patience, should be fine, no time to toy with it right now. $15
Wonderboy III Monster lair - Bootleg, works fine, has a "jamma" biscuit soldered on that isn't exactly jamma, so it will need a new converter. $80
Express Raider - DE original, fully working, clean - $70
Namco 246 /w Tekken 4 - Missing cover and drive fixing plate, works but drive is old, as with most Tekken 4s, it's hard to get booting. Includes I/O, dongle, original disc, missing VGA jumper cable, all else is there. - $150
Street Fighter II Magic Delta Turbo bootleg - Colour errors but works fine, ram banking error, two rams don't get the enable signals, should be an easy fix for those in the know-how, I don't have the time for it. It's also missing a crystal i n the audio section. $30
Virtua Striker 2 - Sega Model 3 step 2.0, missing I/O shield and PCB cage, otherwise complete. Tested with a step 1 I/O shield, just flashes an error code on the leds in cycles, rom board is most likely working. $50
Calofornia Speed - Original Seattle boards, no boot, have three of these, $20 each or $50 for all three
Seattle networking boards, have two, both are working pulls, $15 each or $25 for the pair.
NAOMI Ninja Assault Namco lightgun I/O board, no wiring - $70
Naomi Motherboard - Comes up with error 03 regardless of having a cart installed or no, comes with no I/O shield or casing - $40
Punisher - bootleg, works $40
Dig-Dug bootleg (Zig-zag) - Non-jamma, works, $30
$100 takes the Box of surprise, a large assortment of arcade PCBs in various states of dismay, has some rare older rams that you'd pay $5 a piece if you needed to buy them now, bootleg qix and pacman, various older and newer bootlegs and originals in there (MK3, Naomi mobo, California Speed etc) . Over 20 PCBs, if you love to tinker, there are boards in there I planned to revive but just don't have the time anymore. Shipping overseas will probably be costly on this last item. SOLD
LMK which you need, feel free to make your offers aswell. Use PMs please, will take paypal of course.
For sale:
PCBs:
Stern MPU-200 - fully refurbished, new sockets, virtually no acid damage. $180
Bally -35 MPU - fully refurbished, light acid damage repaired, bad sockets replaced $110
Bally -35 6802 MPU - factory condition, no acid damage at all, original battery still holding charge! $180
Williams system 11c MPU - Acid spill that has been neutralized, fully working SOLD
Data East rev 3 MPU - No acid, fully working when pulled, no game to test in atm $180
Williams System 11b MPU - No acid, fully working. virtually flawless. $180
Williams System 11 MPU - No acid, fully working, virtually flawless. SOLD
Williams System 11 Powersupply - flawless $50
Williams System 11b aux power board - flawless $50
Bally lamp driver - flawless $20
Bally Aux lamp driver - flawless $10
Numeric and Alphanumeric displays, 6 and 7 digit both bally/stern and newer williams, right up to the common board version, with or without driver boards, request a price on these.(2x 16 digit alphanumeric and newer displays available only in very limited quantities.)
Send a PM for details, feel free to make offers too, orders for multiple boards get shipping discounts. Price for one PCB's shipping is $35, registered priority mail. For small boards, shipping's even lower. Orders over $350 get free shipping.
Boards are in collectors condition, meaning they are completely clean, washed in an ultrasonic bath, they basically look new with no hackjobs of any sort. (Exceptions are acid damaged boards, which while cleaned in the same method, will always show the remnants of acid damage.)
Send PMs please.
GAME SPECIFIC PARTS:
Semi-complete Stern Iron Maiden plastics set: $50
Semi-complete Pin-bot plastics set: $30
Semi-complete Goldball plastics set: $30
Semi-complete Firepower II plastics set: $20
Pin-bot blue ramp: $20
F-14 dome-set comes from early production game: $30
FACTORY prototype F-14 roms (meaning original Williams labels) $20
F-14 dome-light assy, motor and belts included, no bulbs $40
High Speed dome-motor assy, no bulb, $30
WWF Royal Rumble apron - flawless $15
Bally Beat the Clock apron - needs cleaning $15
Bally Bobby Orr's Powerplay apron - very nice $20
Gottlieb sys80b apron - very nice, has European operator's plastic moulded logo attached $10
Stern Iron Maiden playfield, VG condition, has two minor flaws, one small wearspot in upper playfield, not noticable unless pointed out, and truss rod wore through the playfield, common problem, can be repaired professionally with little work. Mylar has already been removed, almost fully prepped for restoration work. $200 as-is, or $450 refurbished and clearcoated.
Make your offers, willing to trade for arcade PCBs and will take dead pcbs (Arcade and pinball) for a discount.
Also, I am looking for CPS 1 boards, not complete sets, but separate a, b, c boards and q sound boards to repair some games I have, so if you have any, I'd be glad to incorporate them into a deal.
Shipping up to 2 kgs is $35 worldwide as registered airmail. (Slightly cheaper for european countries)
Puzzle Bobble 3 - 100% $100
Zero Wing - 100%,two player simultaneous play version! $100
F/A - (Japanese Fighter & Attacker) works flawless. SOLD
Asterix - Plays, has some graphics glitches, looks to be either a RAM or ROM failure, self diagnostic passes though. Have resoldered all surface mount chips when I bought it (Bought it completely dead, caught in a reset loop) so the error is not a problem with the SMD components! $30 takes it
Time Scanner - 100% $80
Cadillacs & Dinosaurs Turbo 97- Bootleg, works SOLD
Cadillacs & Dinosaurs Turbo 2000 - Bootleg, overlay graphics glitching and jumping about, should be a fairly easy fix, missing sound amp. $15
Sunset Riders - Bootleg, graphics glitches, plays blind Problem is probably the PLCC socket/chip legs are tarnished, previous 'repairman' put solder onto the chip legs, needs a little patience, should be fine, no time to toy with it right now. $15
Wonderboy III Monster lair - Bootleg, works fine, has a "jamma" biscuit soldered on that isn't exactly jamma, so it will need a new converter. $80
Express Raider - DE original, fully working, clean - $70
Namco 246 /w Tekken 4 - Missing cover and drive fixing plate, works but drive is old, as with most Tekken 4s, it's hard to get booting. Includes I/O, dongle, original disc, missing VGA jumper cable, all else is there. - $150
Street Fighter II Magic Delta Turbo bootleg - Colour errors but works fine, ram banking error, two rams don't get the enable signals, should be an easy fix for those in the know-how, I don't have the time for it. It's also missing a crystal i n the audio section. $30
Virtua Striker 2 - Sega Model 3 step 2.0, missing I/O shield and PCB cage, otherwise complete. Tested with a step 1 I/O shield, just flashes an error code on the leds in cycles, rom board is most likely working. $50
Calofornia Speed - Original Seattle boards, no boot, have three of these, $20 each or $50 for all three
Seattle networking boards, have two, both are working pulls, $15 each or $25 for the pair.
NAOMI Ninja Assault Namco lightgun I/O board, no wiring - $70
Naomi Motherboard - Comes up with error 03 regardless of having a cart installed or no, comes with no I/O shield or casing - $40
Punisher - bootleg, works $40
Dig-Dug bootleg (Zig-zag) - Non-jamma, works, $30
$100 takes the Box of surprise, a large assortment of arcade PCBs in various states of dismay, has some rare older rams that you'd pay $5 a piece if you needed to buy them now, bootleg qix and pacman, various older and newer bootlegs and originals in there (MK3, Naomi mobo, California Speed etc) . Over 20 PCBs, if you love to tinker, there are boards in there I planned to revive but just don't have the time anymore. Shipping overseas will probably be costly on this last item. SOLD
LMK which you need, feel free to make your offers aswell. Use PMs please, will take paypal of course.
For sale:
PCBs:
Stern MPU-200 - fully refurbished, new sockets, virtually no acid damage. $180
Bally -35 MPU - fully refurbished, light acid damage repaired, bad sockets replaced $110
Bally -35 6802 MPU - factory condition, no acid damage at all, original battery still holding charge! $180
Williams system 11c MPU - Acid spill that has been neutralized, fully working SOLD
Data East rev 3 MPU - No acid, fully working when pulled, no game to test in atm $180
Williams System 11b MPU - No acid, fully working. virtually flawless. $180
Williams System 11 MPU - No acid, fully working, virtually flawless. SOLD
Williams System 11 Powersupply - flawless $50
Williams System 11b aux power board - flawless $50
Bally lamp driver - flawless $20
Bally Aux lamp driver - flawless $10
Numeric and Alphanumeric displays, 6 and 7 digit both bally/stern and newer williams, right up to the common board version, with or without driver boards, request a price on these.(2x 16 digit alphanumeric and newer displays available only in very limited quantities.)
Send a PM for details, feel free to make offers too, orders for multiple boards get shipping discounts. Price for one PCB's shipping is $35, registered priority mail. For small boards, shipping's even lower. Orders over $350 get free shipping.
Boards are in collectors condition, meaning they are completely clean, washed in an ultrasonic bath, they basically look new with no hackjobs of any sort. (Exceptions are acid damaged boards, which while cleaned in the same method, will always show the remnants of acid damage.)
Send PMs please.
GAME SPECIFIC PARTS:
Semi-complete Stern Iron Maiden plastics set: $50
Semi-complete Pin-bot plastics set: $30
Semi-complete Goldball plastics set: $30
Semi-complete Firepower II plastics set: $20
Pin-bot blue ramp: $20
F-14 dome-set comes from early production game: $30
FACTORY prototype F-14 roms (meaning original Williams labels) $20
F-14 dome-light assy, motor and belts included, no bulbs $40
High Speed dome-motor assy, no bulb, $30
WWF Royal Rumble apron - flawless $15
Bally Beat the Clock apron - needs cleaning $15
Bally Bobby Orr's Powerplay apron - very nice $20
Gottlieb sys80b apron - very nice, has European operator's plastic moulded logo attached $10
Stern Iron Maiden playfield, VG condition, has two minor flaws, one small wearspot in upper playfield, not noticable unless pointed out, and truss rod wore through the playfield, common problem, can be repaired professionally with little work. Mylar has already been removed, almost fully prepped for restoration work. $200 as-is, or $450 refurbished and clearcoated.
Make your offers, willing to trade for arcade PCBs and will take dead pcbs (Arcade and pinball) for a discount.
Also, I am looking for CPS 1 boards, not complete sets, but separate a, b, c boards and q sound boards to repair some games I have, so if you have any, I'd be glad to incorporate them into a deal.
Shipping up to 2 kgs is $35 worldwide as registered airmail. (Slightly cheaper for european countries)
Last edited:
