[Hyper64] Test Button/Component output ??? (REV2)

Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
I'm finishing the Hyper64 consolized....all its fine...but i cant enter in the test menu.....

The board is REV2.....and the dips are setup to: 2Channel stereo (not mono) and MVS (not jamma)....

I tryed connect the pin15 <> ground.....no lucky....where need i get the signal for the test button ???

Another problem.....i'm using the neobitz component board whitout sync cleaner...and now i testing all things on the board.....but the neobitz works only in composite/s-video....the component output dosent output any signal.

All wires are ok...and the neobitz board its ok too (i tested on my mv-1c)....

Someone know if the Hyper64 dosent like the neobitz board to output video component signal ???

PS:Someone have the REV2 manual pdf archive ???

[]'Macck
 
Last edited:
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
i'm using a real arcade psu.....that gives

+5vcc = 15A
+12vcc = 3A
-5vcc
gnd

Well.....i turn the board ON.....and tryed:

pin15 <> gnd = no
pin M <>gnd = no

When i turn the system ON i got two message....

Now I/O initializing 1.....
Now I/O initializing 2.....

And after that the system starts normal.....

[]'Macck
 
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
Another problem.....i'm using the neobitz component board whitout sync cleaner...and now i testing all things on the board.....but the neobitz works only in composite/s-video....the component output dosent output any signal.

All wires are ok...and the neobitz board its ok too (i tested on my mv-1c)....

Someone know if the Hyper64 dosent like the neobitz board to output video component signal ???

PS:I trying test on my Bravia 32"LCD......

[]'Macck
 
Xian Xi

Xian Xi

JammaNationX,
15 Year Member
Joined
Dec 1, 2005
Posts
27,762
If it's a rev 2 you need to check the switch under the mobo if it is set to jamma or MVS and then assign the test button according to what it is set at. And the Hyper with the Neobitz works fine via component.
 
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
Xian...look....

If i set the board to : MVS and 2ch the test button is M right ?
If i set the board to : Jamma and mono the test button is 15 right ?

I tryed: M <> ground = no lucky
I tryed: 15 <>Ground = no lucky

And about the component...i really dont know whats going on....because i remove the Hyper64 and put any mv-1c board inside of the wood shell....turn it on and works fine on component....i remove the mv-1c and put the hyper64 back and dont get any image in component output....only composite and s-video....

wtf ???

[]'Macck
 
Xian Xi

Xian Xi

JammaNationX,
15 Year Member
Joined
Dec 1, 2005
Posts
27,762
For the encoder, are you using the same header to attach it to the 1C and Hyper? Also which version Neobitz 1.0 or 2.0?
 
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
I'm getting the stereo signal from the conector closed to the sound volume at left of the board....
1,3 = -
2,4 = +

Well the test button resolved (damm broken wire)....now the problem is only the component output......

NeoBitz is rev 2.0.

[]'Macck
 
Xian Xi

Xian Xi

JammaNationX,
15 Year Member
Joined
Dec 1, 2005
Posts
27,762
Does it have a sync cleaner on it? If it does, turn it off. For some reason I find that when the sync cleaner was on it would not display sometimes.
 
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
Yes i'm using the same jamma conector to test the hyper and 1c board.....

[]'Macck
 
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
No Xian it dosent have the sync cleaner.....

[]'Macck
 
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
What do that 4 jumpers in the bottom of the board ???

Mine are all to off !!!

[]'Macck
 
Xian Xi

Xian Xi

JammaNationX,
15 Year Member
Joined
Dec 1, 2005
Posts
27,762
What 4 jumpers? I know the Neobitz works on the Hyper for Component because I used to play mine that way all the time.
 
Macck

Macck

Edo Express Delivery Guy
Joined
Nov 17, 2005
Posts
338
Now the video component works fine.....i dont know why...but only works if i improve the sync cleaner on the board....

Thanks to all !!!

[]'Macck
 
xiao_haozi

xiao_haozi

Avid Neo-Expert
Joined
Jan 22, 2009
Posts
1,977
What did you have to do with the sync cleaner to get it going?

And is this one of the newer neobitz boards?

Glad to hear you have it working Macck.... is it all finished?
 
Xian Xi

Xian Xi

JammaNationX,
15 Year Member
Joined
Dec 1, 2005
Posts
27,762
Looks like a book case I used to have, Macck I hope thats not MDF, that's a little thin looking bro.
 
You must log in or register to reply here.
Top