Page 3 of 3 FirstFirst 123
Results 51 to 55 of 55

Thread: Unmame MVS-4-25 (ver. 3) restoration

  1. #51
    Neo Bubble Buster
    DaveyDarko's Avatar
    Join Date
    Apr 2015
    Location
    Florida, United States

    Posts
    45
    Installed the EL panels tonight! I had to put in a claim with ebay to get the sellers attention a month after I paid for them, but I was not really in a big rush to get the parts. Im just glad they got here finally and I did not get ripped off xD
    I actually ended up mounting the board on the lower half out of fear that there might have been some feed back through the speakers.
    c9fbcropped.jpg


    The camera was crooked, It was hard to get a good pic while holding the marquee open
    DSCN0001_marquee_1024.jpg

    1 out of 4 isn't bad I guess lol
    I was really expecting them to not work at all honestly xD
    DSCN0026_1024.jpg

    DSCN0023_cropped1024.jpg

    Gonna have to hop over to glowhut.com and pick up some replacement panels
    Last edited by DaveyDarko; 03-31-2016 at 01:19 AM.


    Parts needed to finish my cab:
    PCB, MV-IC with cables

  2. #52
    Neo Bubble Buster
    DaveyDarko's Avatar
    Join Date
    Apr 2015
    Location
    Florida, United States

    Posts
    45
    #1, #2, and #3 are starting to light up a LITTLE bit. Maybe they will get brighter if I leave it on for a while.
    One thing I have noticed is that the driver board is making a high pitched whine when on one of the slots with a dead EL panel. Im going to disconnect the driver board to avoid stressing it out until I get the replacement panels from glowhut.com
    Last edited by DaveyDarko; 03-31-2016 at 08:30 AM.


    Parts needed to finish my cab:
    PCB, MV-IC with cables

  3. #53
    Thou Shalt Not
    Question Rot.
    xsq's Avatar
    Join Date
    Jan 2013
    Location
    Muenster, Germany

    Posts
    7,420
    well, it's looking better every time I check in here, good job!

  4. #54
    Kuroko's Training Dummy
    alby13's Avatar
    Join Date
    Sep 2013
    Location
    California, USA

    Posts
    71
    This is just a cool project read
    -alby13

    Proud owner of a 1 slot & 4 slot MVS

    "A samurai fears not death. Struggles to triumph over evil. And lives for one purpose: To destroy all enemies."

  5. #55
    Neo Bubble Buster
    DaveyDarko's Avatar
    Join Date
    Apr 2015
    Location
    Florida, United States

    Posts
    45
    Quote Originally Posted by xsq View Post
    well, it's looking better every time I check in here, good job!
    Thanks for keeping up with me! I've really had good luck so far and its been alot of fun!

    Quote Originally Posted by alby13 View Post
    This is just a cool project read
    Thanks! I'm sorry about the crappy out of focus pictures. I REALLY wish I would have purchased a better camera sooner. When I look back at the first posts it makes me cringe a little xD
    Last edited by DaveyDarko; 04-02-2016 at 03:13 AM.


    Parts needed to finish my cab:
    PCB, MV-IC with cables

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •