Page 2 of 2 FirstFirst 12
Results 26 to 40 of 40

Thread: Consolized Naomi system

  1. #26
    Timid Neo Newbie

    Join Date
    Nov 2006
    Location
    Bakersfield,CA

    Posts
    6
    Well I got the I/O mounted inside. The wiring aint puurrrtie but its functioning so far. I dont have those fancy connectors that MLK has plus I hard wired some ghetto molex for power. Only thing left is to mount the controll ports and wire them in. This is the only thing Im scared off. Im fearing Ima damage the plastic and make it look ugly. Any suggestions.

  2. #27
    Timid Neo Newbie

    Join Date
    Nov 2006
    Location
    Bakersfield,CA

    Posts
    6
    Yesterday I had the I/O working with my new wiring, today I tried to wire in the controls and Im getting an I/O not found Any ideas what Im doing wrong?

  3. #28

    MKL's Avatar
    Join Date
    Mar 2002
    Location
    Italy

    Posts
    3,612
    Quote Originally Posted by metROCK
    Yesterday I had the I/O working with my new wiring, today I tried to wire in the controls and Im getting an I/O not found Any ideas what Im doing wrong?
    You wired controls through a standard disconnectable jamma connector or are they hardwired to the PCB? If it's the former what happens when you disconnect the controls? Normally whether the controls are wired or not it doesn't make any difference: once the I/O is getting power and is connected to the motherboard via the USB cable you shouldn't get that error message.

  4. #29
    Timid Neo Newbie

    Join Date
    Nov 2006
    Location
    Bakersfield,CA

    Posts
    6
    I thought that the usb cable does not give power and thats why there was additional power hooked up. I forget where I had read that and assumed thats why you hooked up this jumper wire on the I/O usb area http://img67.imageshack.us/img67/7353/e6ey6.jpg. First I had made a cable to replace the usb cable since Im mounting my I/O on the inside in your fashion. Then I hooked up the 5v power and ground like so in this pic http://img177.imageshack.us/img177/6944/h3qu8.jpg with one difference. From the looks of the pic the 5v is hooked up to pins 2/3 and ground is hooked up to 12/13 on CN3. Shouldnt the 5v be on pins 1/2 and ground be on pins 13/14 like the I/O board on this page http://solvalou.mine.nu/beginner/naomi.html#sega_io I used pins 1/2 and 13/14. For my intitial test I mounted on the inside of the case I power up and everything was fine. I let it run for about an hour before turned it off.

    My next step I am hard wiring the controls directly to the I/O pcb. I wired in player one just to test. I wired the directions, six inputs,start,coin,ground, and 5v to a modded pad. Im testing the street fighter anny pad as my controller. I have everything wired properly (I think and I hope I do ) so I power up with out the pad plugged in and I get the I/O board not found


    If the USB needs power how much does it need.

  5. #30

    MKL's Avatar
    Join Date
    Mar 2002
    Location
    Italy

    Posts
    3,612
    Quote Originally Posted by metROCK
    I thought that the usb cable does not give power and thats why there was additional power hooked up. I forget where I had read that and assumed thats why you hooked up this jumper wire on the I/O usb area http://img67.imageshack.us/img67/7353/e6ey6.jpg.
    The I/O is in fact not powered through the USB cable. In any case the wire in that pic has nothing to do with that (it's for using the other USB port), better leave it alone.

    Quote Originally Posted by metROCK
    First I had made a cable to replace the usb cable since Im mounting my I/O on the inside in your fashion. Then I hooked up the 5v power and ground like so in this pic http://img177.imageshack.us/img177/6944/h3qu8.jpg with one difference. From the looks of the pic the 5v is hooked up to pins 2/3 and ground is hooked up to 12/13 on CN3. Shouldnt the 5v be on pins 1/2 and ground be on pins 13/14 like the I/O board on this page http://solvalou.mine.nu/beginner/naomi.html#sega_io I used pins 1/2 and 13/14.
    Pins 1, 2, 3 are all +5v and pins 12, 13, 14 are all grounds so using 1/2 or 2/3 etc. is the same thing.

  6. #31
    Timid Neo Newbie

    Join Date
    Nov 2006
    Location
    Bakersfield,CA

    Posts
    6
    Well Ima unhook the wires the I did last night and see if that has any effect. Ill leave the power/ground wires where I have em coming into the I/O. I will remove that wire that you mentioned from the usb. Im at a loss here again. thanks for your help so far MKL.

  7. #32
    New Challenger
    xunxun's Avatar
    Join Date
    May 2014
    Location
    china

    Posts
    20
    Hello. MKL~
    I like you in this NAOMI MOD tutorial.
    But your picture has failure, I hope you can provide the picture again, I really want to learn.
    Or you can provide your email address, we can communicate by e-mail under.
    Thank you very much!

  8. #33
    Trollbox Trade Federation
    bustedstr8's Avatar
    Join Date
    Oct 2007
    Location
    Boston Burbs

    Posts
    1,010
    Translation

    Quote Originally Posted by xunxun View Post
    Hello. MKL~
    I want you in this NAOMI MOD tutorial.
    But your picture has failure, I hope you can provide the picture again, I really need to learn asap.
    I have two containers of chained 14 year old workers and solder equipment...and rice is running much low.
    Or you can provide your email address, we can communicate by e-mail under.
    Soon contact me please or starvation will destroy profits.
    Clowns Suck


  9. #34
    New Challenger
    xunxun's Avatar
    Join Date
    May 2014
    Location
    china

    Posts
    20
    Quote Originally Posted by bustedstr8 View Post
    Translation
    My English is not good. There are some grammatical errors.
    But I'm hoping to get help

  10. #35
    New Challenger
    xunxun's Avatar
    Join Date
    May 2014
    Location
    china

    Posts
    20
    20140529 NAOMI2 ?????_019.JPG

    NAOMI2 Silent fan

  11. #36

  12. #37
    Dogg-Father
    Neodogg's Avatar
    Join Date
    Nov 2002
    Location
    Cincinnati, OH

    Posts
    2,572
    Interesting adapter
    _ _ ___________________________ _ _
    People I've delt with:
    |Steve Rhine|Vinh|Jeff Kurtz|Kenny Boy|Big Bear|Fox1|Bones|Kid Aphex|Bluevoodu|Kubikiri Basara|Shawn|Michael Yagami|

  13. #38
    Cheng's Errand Boy

    Join Date
    Oct 2008
    Location
    UK

    Posts
    124
    I know this is an old thread but I am interested in this mod. All the links to the images are now dead, would anyone be able to re-upload them?

  14. #39
    Mauru's Zoo Manager
    werejag's Avatar
    Join Date
    May 2005
    Location
    Oklahoma

    Posts
    2,881
    a while ago a few years ago i got the pics from mkl and recreated the guide for my own files. here it is https://www.dropbox.com/s/c7u4ymw3rf...ystem.rar?dl=0
    I guess it's a good day for Were-Jag... -NG: DEV.TEAM
    It's only fucking 50 USD for crying out loud. -Yakumo
    If there's one thing I hate in life more than anything else it's freeloaders. -Yakumo
    "reality has a well-known liberal bias." - Stephen Colbert

  15. #40
    Bashful Neophyte

    Join Date
    Apr 2008
    Location
    Houston Tx

    Posts
    17
    Hey guys, sorry to reply to such an old thread. I am trying to consolize a sega naomi but I am having difficulties finding any worthwhile documentation on it. The links on this post are dead and I am not sure how to get in touch with MKL. Is there some one who could assist me in this? I have a couple naomi boards and a capcom I/O. Any assistance is greatly appreciated. Again, sorry for posting in such an old thread.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •