WG 25K7193 Monitor issue

Syn

Syn

There can be only one.
10 Year Member
Joined
Jan 21, 2009
Posts
9,091
Well I just hooked up the monitor in my Dynamo HS-5 25" screen and I see this



I know how to discharge a monitor but my soldering skills are extremely poor (hand twitches a little bit especially if I concentrating).



Any suggestions are needed.

Even if it's so I don't sound like a total dumb fuck on the phone.

There's so much I feel comfortable with changing on a cab (harness, joysticks, buttons, cp) that of course, a problem arises in the one area I'm poor in.
 
Last edited:
Kid Panda

Kid Panda

The Chinese Kid
Joined
Jun 13, 2010
Posts
12,514
What kind of monitor is it exactly? Have you fiddled with any of the pots on the chassis itself?
 
Syn

Syn

There can be only one.
10 Year Member
Joined
Jan 21, 2009
Posts
9,091
Kid Panda said:
What kind of monitor is it exactly? Have you fiddled with any of the pots on the chassis itself?
Click to expand...

Wells Gardner 25k7193

I've turned a few pots but fear I'm making things worse.
 
Last edited:
daskrabs

daskrabs

Ace Ghost Pilot
10 Year Member
Joined
Aug 23, 2010
Posts
1,314
synbiosfan said:
Wells Gardner 25k7193
Click to expand...

Try fiddling with the pots on the remote board. They short/break easily. Reflow the solder on them if possible. Otherwise, try adjusting the brightness pot on the flyback.
 
Kid Panda

Kid Panda

The Chinese Kid
Joined
Jun 13, 2010
Posts
12,514
Looks like your horizontal hold is messed up, like Dask said, trying turning the pots on the remote board.
 
daskrabs

daskrabs

Ace Ghost Pilot
10 Year Member
Joined
Aug 23, 2010
Posts
1,314
If it is the H-Hold at fault, I think that pot's on the chassis itself and not the remote board. More than one issue possibly.
 
Syn

Syn

There can be only one.
10 Year Member
Joined
Jan 21, 2009
Posts
9,091
Turning the h hold either way makes it worse.

it is on the chassis.

it had to be the vert cab damnit.
 
Last edited:
Kid Panda

Kid Panda

The Chinese Kid
Joined
Jun 13, 2010
Posts
12,514
Try turning the Vertical hold pot. That one should be on the remote board.
 
Syn

Syn

There can be only one.
10 Year Member
Joined
Jan 21, 2009
Posts
9,091
Last edited:
KaPH33n

KaPH33n

Sieger's Squire
Joined
Jan 28, 2010
Posts
819
what about other boards on the cab? some shooters have weird sync issues with cabs but work on superguns fine. don't know if this is one of those or what...
 
Syn

Syn

There can be only one.
10 Year Member
Joined
Jan 21, 2009
Posts
9,091
I dropped it off today. I showed him pictures of what it was doing and he asked a bunch of questions. Just glancing at it, there's no obvious problems.

So I went back to replacing other shit on the Dynamo, the power supply died. No marquee light, fan blowing or sound. It was fine, yesterday. :(

When I took a good look at the PS, I saw masking tape with "works? 12v low".

Ordered a new one from a guy 300 miles away so I shouldn't have to wait long.
 
Syn

Syn

There can be only one.
10 Year Member
Joined
Jan 21, 2009
Posts
9,091
It turned out to be the flyback was cracked all to hell. With a replacement, it's fine now.
 
You must log in or register to reply here.
Top