- Joined
- Mar 4, 2001
- Posts
- 1,274
I originally had these pieces printed proffesionally on thick vinyl with UV resistant inks for framing. I was going to hang them in my arcade room but I ended up selling all my arcade cabs. So now I must part with them. Keep in mind that most of these cost me $20 a square foot plus setup fees unless noted. These are not inexepensive prints made on glossy photo paper(except one), these are on thick vinyl canvas. I am willing to take a little loss on them just like my cabinets since I have no place for these now. 
A few of these prints were in a tube near a water heater that exploded, so they have faint yellow around the edges of the vinyl where water touched them. This will not effect the print itself, nor your ability to frame them. I will describe each of these prints in detail.
Click on the pics for enlarged versions. The dimensions I am posting are the image dimensions. The pieces of vinyl themselves are much larger to allow room for attaching a matte for framing. The pics are not perfect because of my junky camera, these pieces look awesome in person. They are all high quality prints from high res(600+dpi) sources.
Shiki - Height 29.5" Width 26"
originally paid over $100, will let it go for $70 shipped
Leona - Height 26" Width 22"
This one has a printing error, the bottom text is slightly cut off. I got this one fairly cheap because of this so I will let it go for $45 shipped
Mai - Height 35.5" Width 23"
This piece was the only one printed on glossy photo paper that cost me $10 a square foot. it has a small kink in the paper every seven inches lenghtwise. The kink is about 5 inches in from the left side. This is due to the exploding water heater I mentioned earlier. It is not terribly noticeable but I wanted to make it clear to any buyers that it is not perfect. $45 shipped
Last Blade - Height 31.5" Width 22.5"
This is one of my favorite pieces of Last Blade art, so I could not help but make a print of it. THis is one of the few that got water on the edges and if you look at the very top and bottom you'll see yellowing of the excess vinyl. It is not noticeable in the print image AT ALL! Once properly framed the effected area would be cut off anyways. Over $100 cost to me, $75 shipped to you.
Now for the two best prints:
Kula - Height 33.5" Width 30.5"
This print is amazing, only trumped by the one of K' below. It is a stunning piece of art and reproduced well in a large print. This one has yellowing on the bottom of the vinyl, but once again, this will not mean anything once framed. This one ran me $150 but you get to grab it for a flat $100 shipped to your doorstep.
K' - Height 34" Width 31"
This one is my favorite. It is visually arresting and uses a great color. This would look perfect in a game room or as a "pop art" looking piece for a main room.It has the yellowing on the edges of the vinyl but does not effect the picture itself. Once again, it ran me $150 and you can take it for a flat $100 shipped.
Just PM me if you are interested. I would prefer money right now as I am trying to purchase a new LCD TV. For trades I would only accept Supergun items like a Neobitz Board. Not looking for much PCB wise unless you have a CPS2 D&D SoM blue board, don't need a full kit.
Just let me know!
A few of these prints were in a tube near a water heater that exploded, so they have faint yellow around the edges of the vinyl where water touched them. This will not effect the print itself, nor your ability to frame them. I will describe each of these prints in detail.
Click on the pics for enlarged versions. The dimensions I am posting are the image dimensions. The pieces of vinyl themselves are much larger to allow room for attaching a matte for framing. The pics are not perfect because of my junky camera, these pieces look awesome in person. They are all high quality prints from high res(600+dpi) sources.
Shiki - Height 29.5" Width 26"
originally paid over $100, will let it go for $70 shipped
Leona - Height 26" Width 22"
This one has a printing error, the bottom text is slightly cut off. I got this one fairly cheap because of this so I will let it go for $45 shipped
Mai - Height 35.5" Width 23"
This piece was the only one printed on glossy photo paper that cost me $10 a square foot. it has a small kink in the paper every seven inches lenghtwise. The kink is about 5 inches in from the left side. This is due to the exploding water heater I mentioned earlier. It is not terribly noticeable but I wanted to make it clear to any buyers that it is not perfect. $45 shipped
Last Blade - Height 31.5" Width 22.5"
This is one of my favorite pieces of Last Blade art, so I could not help but make a print of it. THis is one of the few that got water on the edges and if you look at the very top and bottom you'll see yellowing of the excess vinyl. It is not noticeable in the print image AT ALL! Once properly framed the effected area would be cut off anyways. Over $100 cost to me, $75 shipped to you.
Now for the two best prints:
Kula - Height 33.5" Width 30.5"
This print is amazing, only trumped by the one of K' below. It is a stunning piece of art and reproduced well in a large print. This one has yellowing on the bottom of the vinyl, but once again, this will not mean anything once framed. This one ran me $150 but you get to grab it for a flat $100 shipped to your doorstep.
K' - Height 34" Width 31"
This one is my favorite. It is visually arresting and uses a great color. This would look perfect in a game room or as a "pop art" looking piece for a main room.It has the yellowing on the edges of the vinyl but does not effect the picture itself. Once again, it ran me $150 and you can take it for a flat $100 shipped.
Just PM me if you are interested. I would prefer money right now as I am trying to purchase a new LCD TV. For trades I would only accept Supergun items like a Neobitz Board. Not looking for much PCB wise unless you have a CPS2 D&D SoM blue board, don't need a full kit.
Just let me know!
